Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours ยท Estimated delivery Jul 6 - Jul 11
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Cactus, 5in, Cereus Peruvianus MonstroseThe Cereus Peruvianus cactus is a beautiful, knobby cactus with average length yellow orange spines. If you need any more photos or additional information on this product, send us a message using the chat button on our website with the product name, and we will get back to you as soon as possible. This plant has a representative product photo and the item you will receive may not be exactly as shown. Attributes Type: Houseplant, Cactus Height: 48 in
The Cereus Peruvianus cactus is a beautiful, knobby cactus with average length yellow/orange spines.
If you need any more photos or additional information on this product, send us a message using the chat button on our website with the product name, and we will get back to you as soon as possible.
This plant has a representative product photo and the item you will receive may not be exactly as shown.
Attributes
Type: Houseplant, CactusHeight: 48 in - 72 in
Spread: 36 in - 60 in
Light: Full Sun
Water: Low
Zone: 9 - 11
Pet Safe: Non-Toxic, minor puncture threat
Care
General Maintenance: Repot your cactus once it has doubled in size, or each year - whichever comes first. These cacti are very easy to take care of and appreciate a bright sunny spot and tons of neglectTemperature: 0 to 55 degrees Celsius is this plant's hardiness range
Light: These cacti love sunlight, keep within 1m of a South facing window for optimum growth. They can also be kept outdoors in a sunny spot during the summer and hot season. Gradually introduce them to full sun by first putting them in a spot of full shade and move them to a slightly sunnier location every couple of days. These plants are not tolerant of low light
Watering: Cacti are very efficient with water, and store tons of moisture inside their leaves and trunks. Therefore, they do not require near as much watering as many other plants. Water when the top 50-70% of soil is completely dry. They will require slightly more water in brighter light and hotter conditions. During the dormant season water once every 2-3 months
Soil: Cacti love a well-draining, dry soil blend. Their roots are sensitive to rot. Any high-quality cactus / succulent soil blend will allow these plants to thrive
Fertilizer: These cacti rarely need fertilization, but will benefit from a diluted balanced houseplant fertilizer once every 2-3 months during the growing season
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.9 โ
โ
โ
โ
โ
Based on 1194 reviews
Sort
Product Reviews
โ
โ
โ
โ
โ
4
Oily situation lol
Configuration: 4-Stroke, Size: 1 GA
Honestly how do you write a review of this product? I would have to run tests for years on multiple oils on various engines to do so. The value was good however and shipping was great
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 31, 2025
โ
โ
โ
โ
โ
5
Use the best oil to protect your investment
Configuration: 4-Stroke, Size: 1 GA
Great product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
โ
โ
โ
โ
โ
5
Works well. You need to drill a 3/8โ hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4โ towards the stepped part of the alignment tool (this is so you wonโt bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8โ diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8โ diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4โ drill first, using plenty of oil, drill all the way through, then use the 3/8โ drill, deburr both sides and you should be good to go. People complain that it doesnโt come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure youโre perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
โ
โ
โ
โ
โ
5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
โ
โ
โ
โ
โ
5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023